Identificador: 2458
Abierta
ID de articulo : # 2458 se ha agregado a su lista de deseos.
Descripción
PARTE: 12572 - PRENSA DE RADIO FRECUENCIA - OGDEN
USADA - BUENAS CONDICIONES
Curing area: 36” x 60” x 2” thick.
Clamping pressure is applied by multi-power (dual pistons on a common shaft) pneumatic cylinders to maximize pressure while relying on standard plant pressures. Unlike presses without multi-power cylinders, which require booster compressors, the Model SL36x60 reaches full capacity at 100-psi plant air pressure.
Edge pressure is applied by eight (8) each pusher shoes, each with a 4” bore x 4” stroke twin-piston multi-power pneumatic cylinders.
Top platen pressure is applied by two (2) 5” diameter x 16” stroke pneumatic cylinders through a cantilever arm that keeps the footprint to a minimum while still allowing the operator full access to the platen area.
The platen is set at a 45-degree angle and the top platen opens wide; allowing the operator to step inside the press for ergonomic and accurate parts placement.
The internal solid state RfsProtech 6KW Generator cures approximately 600 square inches of glue line per minute.
The Generator features solid state rectifiers and all aluminum cabinet for maximum conductivity and superior performance.
Two-hand no-tie-down safety controls for closing the top platen.
Controls are simple to understand, and are complete with the required push-buttons, switch, meters, digital operator display, and on-screen troubleshooting diagnostics.
The machine is controlled by a PLC for dependability and efficient maintenance. All controls will be provided for safe and efficient operation. The operator screen permits efficient operation, and the included press diagnostics screens assist in trouble-shooting when the need arises.
Proper interfaces will be provided for operational signals and emergency system stop.
All necessary RF controls, including buttons, meters, and PLC operator interface panel are mounted on a control panel attached to the left front of the press.
Interlocked top platen and safety switches on all access doors insure operator safety.
Power requirements are 480 volt, 60 cycle, 3 phase electric.
Circuit breaker protection is provided. A service disconnect is required for safety, but is not provided.
Powered In-Feed table with motor and controls
Out-feed steel deck
Voltage 480 volts 60 Hz
Pago y Devoluciones
- Forma de pago
- Transferencia/Deposito Bancario
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery
LIJADORA DE CEPILLOS – SLIPCON
PARTE:
12151 - LIJADORA DE CEPILLOS – SLIPCON
USADA – EN MUY BUENAS
CONDICIONES
- The patented combination of rollers and rotating / oscillating discs makes
the Perfection DBB 1350 sanding machine the ideal finishing solution for entry
doors, cabinet doors, drawer fronts, sheet goods, shutters, face frames,
furniture parts and much more.
- The sander works equally well for whitewood sanding and stain/sealer or
primer sanding. Can be used with both traditional and UV cured coat...
AMXmachinery
ASTILLADOR A GASOLINA – 13.5 HP – MAX DIAMETRO 4.5”
PARTE:
2EB-MDWC1500 - ASTILLADOR A GASOLINA – 13.5 HP – MAX DIAMETRO 4.5”
NUEVA CON GARANTIAElectric
Start (Battery included), Emergency Stop Lever for Safety,Powerful
13 1/2 HP B&S Gasoline Engine, 4-stroke, air-cooled,Efficient
Disc Rotor cutting up to 4 1/2 in. in diameter,360
degrees rotatable Discharge Chute, 2"
Ball Trailer Hitch,Self-feeding
gasoline engine powered that uses a large disc rotor. Compared to most others
which use a drum style processor, this machine is mo...
AMXmachinery
ASERRADERO PORTATIL - 14 HP GASOLINA - 31” DIAMETRO
PARTE: 2EB-WP-031 - ASERRADERO PORTATIL - 14 HP GASOLINA - 31” DIAMETRO
Nuevo con garantía
Engine: Kohler
Command Pro CH440 - 14HP Electric Start
Displacement:
429CC
Start type:
Recoil Electric Start
Oil capacity:
1.16L
Cast iron cylinder
liners provide lasting durability
Oil Sentry
automatic low oil engine shutdown system
Cutting Capacity:
31" x 7" x 110" ** We can add around 6 feet of track optionalMaximum Board
Thickness: 7"
Standard Track
Size: 157" x...
AMXmachinery
PARTE: 12339 - LIJADORA - CALIBRADORA - 3 LIJAS BANDA -1 CEPILLO
PARTE: 12339 - LIJADORA - CALIBRADORA - 3 LIJAS BANDA -1 CEPILLO
USADA BUENAS CONDICIONES
La
máquina se retiró trabajando en buenas condiciones